| 包裝數量 (單位: pcs) |
| 規格 | 內襯塑帶 |
| LRC12 | 2,000 |
| 內襯塑帶規格 (單位: mm) |
 |
| 阻值 (mΩ) | A | B | W | E | F | P0 | P1 | P2 | ΦD0 | T |
| 0.50 | 3.40±0.1 | 6.70±0.1 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 1.40±0.1 |
| 0.75 | 3.50±0.1 | 6.80±0.2 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 1.35±0.1 |
| 1~20 | 3.40±0.1 | 6.70±0.1 | 12.0±0.1 | 1.75±0.1 | 5.5±0.05 | 4.0±0.05 | 4.00±0.1 | 2.0±0.05 | 1.50+0.1 | 0.80±0.1 |
| Notice:
1. The cumulative tolerance of 10 sprocket hole pitch is ±0.2mm.
2. Carrier camber shall be not more than 1mm per 100mm through a length of 250mm. 3. A & B measured 0.3mm from the bottom of the packet. 4. t measured at a point on the inside bottom of the packet to the top surface of the carrier. 5. Pocket position relative to sprocket hole is measured as the true position of the pocket and not the pocket hole. |
| 環境測試 |
| 項目 | 標準 | 測試方法 | |
| Black coating | Green coating | ||
| 溫度系數 | 視規格而定 |
MIL-STD-202 條件 304 +25/-30/+25/+130/+25°C。 |
|
| 耐熱性 | ±0.5%+0.5mΩ |
±1% |
MIL-STD-202 條件 107G -55°C~150°C，100 次循環 。 |
| 短時間過負載 | ±0.5%+0.5mΩ |
±1% |
JIS-C-5202-5.5 RCWV*2.5 or 最大過負荷電壓 5 seconds。 |
| 耐乾旱性 | ±1%+0.5mΩ |
±1% |
JIS-C-5202-7.2 96 小時 @ +125°C 無負載狀況下。 |
| 負載壽命 | ±1%+0.5mΩ |
±1% |
MIL-STD-202 M108 RCWV，70°C，1.5 小時開，0.5 小時關 1000~1048 小時。 |
| 耐焊溫度 | ±0.5%+0.5mΩ |
±1% |
MIL-STD-202F 條件 210E 260±5°C，10±1second。 |
| 焊接性 | 95%min coverage |
MIL-STD-202F 條件 210E 260±5°C，2±0.5second。 |
|
| Remark: 儲存溫度： 25±3°C；濕度：< 80%RH |
| 如何訂購 |
| LRC | 12 | J | T | K | S | R003 | G | |||||||||||||||||||||||||||||||||||||||||||||||||||||||||
 |
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
|
|
|
|
|
|
|
|
|||||||||||||||||||||||||||||||||||||||||||||||||||||||||
| Current Sensing Resistors |
| Page: 1 / 2 |
| 德鍵電子工業股份公司 臺灣電話﹕+886-2-29810109﹔傳真﹕+886-2-29887487 大陸電話﹕+86-755-26055363﹔傳真﹕+86-755-26055365 |